gemeinsam zwiften | youtube | forum heute
Triathlon Trainingslager Südbaden
Keine Flugreise
Deutschlands wärmste Gegend
Kilometer sammeln vor den Wettkämpfen
Traumhafte Trainingsstrecken
Training auf dem eigenen Rad
25.05.-02.06.2024
EUR 390,-
Reynolds Carbon Clincher - triathlon-szene.de | Europas aktivstes Triathlon Forum
Zurück   triathlon-szene.de | Europas aktivstes Triathlon Forum > Ausrüstung, Material, Bücher > Material: Bike
Registrieren Benutzerliste Suchen Heutige Beiträge

Antwort
 
Themen-Optionen
Alt 19.07.2018, 17:26   #1
bentus
Szenekenner
 
Registriert seit: 11.06.2012
Beiträge: 1.137
Reynolds Carbon Clincher

Hallo,

Bei meinem Canyon Speedmax waren die Reynolds Laufräder dabei. Diese sind tubless ready und es ist wahnsinnig schwer, den Reifen hoch und runter zu montieren. Habe schon verschiedene Reifen probiert. Würde gerne Conti Granprix TT 25mm hinten und den 4000IIs vorne montieren + Latexschläuche, aber ich traue mir die Montage bei den Laufrädern nicht zu. Kann man da ein anderes Felgenband drauf machen, liegt es eventuell daran? Oder habt ihr sonst noch Tipps?
Stellt mich echt vor ein Problem.
Viele grüße
bentus ist offline   Mit Zitat antworten
Alt 19.07.2018, 18:00   #2
tobi.tobsn
Szenekenner
 
Registriert seit: 29.05.2018
Beiträge: 61
Hi,

ich hatte bei meinem letzten Crosser das gleiche Problem. Habe mehrere erfahrene Radfahrer um Hilfe gebeten, aber keiner konnte mir helfen.

Was ich gemacht habe:
Habe mir ein Klettband geholt und den Reifen so weit es geht auf die Felge montiert. Dann den Mantel mit dem Klettband auf einer der Seiten fixieren. Wichtig hier ist, dass dort der Mantel schon in der Felge sitzt.
Dann 2 Heber - einen ganz relativ weit außen und den 2. zwischen dem Klettband und dem 1. Heber. Dann mit Kraft beide Heber betätigen.
Dafür braucht man Kraft, aber ist mit Erfolg gekrönt.

Das Video hat mir damals sehr geholfen:
https://www.youtube.com/watch?v=vFqpCWys3eI&t=2s

Gruß
Tobias
tobi.tobsn ist offline   Mit Zitat antworten
Alt 19.07.2018, 19:01   #3
StanX
Szenekenner
 
Benutzerbild von StanX
 
Registriert seit: 03.03.2012
Beiträge: 1.940
Wenn du jetzt schon Probleme hast, würde ich es mit den Latexschläuchen überdenken. Die Chance hier etwas einzuklemmen, ist meiner Erfahrung nach deutlich größer als ei Butyl.
__________________
Sebastian Bechtel: Talent ist doch nur ein Vorwand sich nicht in die Fresse schlagen zu müssen...

Strava: https://www.strava.com/athletes/5087489

Instagram: https://www.instagram.com/handbike_sdl/?hl=de
StanX ist offline   Mit Zitat antworten
Alt 19.07.2018, 19:54   #4
bentus
Szenekenner
 
Registriert seit: 11.06.2012
Beiträge: 1.137
Zitat:
Zitat von StanX Beitrag anzeigen
Wenn du jetzt schon Probleme hast, würde ich es mit den Latexschläuchen überdenken. Die Chance hier etwas einzuklemmen, ist meiner Erfahrung nach deutlich größer als ei Butyl.
Ja genau das ist das Problem. Beim Rennrad hab ich Latex ohne Probleme montieren können aber genau davor hab ich Sorge, will nicht, dass mir der Reifen um die Ohren fliegt, andererseits hätte ich am TT gerne die Wattersparniss.
bentus ist offline   Mit Zitat antworten
Alt 19.07.2018, 20:51   #5
andas
Ist alles so schön bunt hier!
 
Registriert seit: 21.08.2009
Beiträge: 20
Hi,

Hatte das gleiche Problem.
Mit ein bisschen Routine klappt Reifenwechsel ganz einfach.

Ganz wichtig der reifen muss auf einer Seite in der Felgenmitte sein.

Antwort von Reynolds
Some tires in particular can be hard to fit to our wheel, to assist with these I have listed below the method that we use for mounting:



1. Place the first side of the tire into the rim bed, make sure that the tire bead is sitting in the center of the rim bed at the lowest possible point, if tubed you can then place the tube inside of the tire and push the valve stem through the valve stem hole.

2. Once the first side of the tire is in the rim bed with the tube tucked into the tire you can begin to mount the second side of the tire.

3. Begin mounting the second side of the tire opposite of the valve stem hole working towards the valve so that the last part to mount is directly opposite the valve stem hole.

4. Once you have the tire about 75% of the way mounted and it becomes difficult to set the tire into the rim bed go back to the opposite of the valve stem hole and pinch both sides of the tire to place the tire hook in the center of the rim bed, do this along the entire wheel working away from the valve same as mounting the tire.

5. Once you work your way back to the unmounted end of the tire use the pads of your thumbs and fingers to pinch and roll the tire up over the hook and mount the final portion of the rim.

6. If you cannot get the tire mounted with just your hands then complete steps 1-5 then use a plastic tire lever on the final portion to pop the tire up over the hook and into the rim bed.



Please make sure that if tire levers are used they are plastic, not metal to avoid damaging the carbon rim. Also, always make sure that when re-inflating you allow the rim to ‘Pop’ into place for the tire bead to set in the rim hook, this will avoid hop and tire blowouts.



A few additional tips for those really stubborn tires:

1. Before attempting to mount tire soak the tire in boiling water to expand the tire slightly, apply while still warm but not burning for a more flexible tire and easier fit, once it cools the tire will resort to correct size and position.

2. Before fitting tire apply baby/talcum powder to the circumference of the brake track to assist in slipping the tire bead over the rim hook

3. Once fitted 75% of the way place some hand soap on the remaining portion of the brake track to assist in slipping the tire bead over the rim hook.
andas ist offline   Mit Zitat antworten
Alt 19.07.2018, 21:36   #6
iChris
Szenekenner
 
Benutzerbild von iChris
 
Registriert seit: 29.08.2013
Beiträge: 3.214
Wenn du nicht tubeless fährst kannst du auch einfach das Felgenband tauschen. Das blaue Reynolds trägt relativ viel auf. Mit einem dünneren hast du mehr Spiel.
iChris ist offline   Mit Zitat antworten
Alt 19.07.2018, 22:01   #7
NBer
Szenekenner
 
Benutzerbild von NBer
 
Registriert seit: 21.11.2008
Ort: Neubrandenburg
Beiträge: 6.865
habe auch n neues canyon mit diesen laufrädern. meine erfahrung.....bremswirkung der verbauten reynolds bremsgummis bei nässe gleich null. unbedingt selbst mal ausprobieren, bevor man vll im rennen das erste mal nass fährt und im graben landet.
auf anraten von technikaffineren leuten habe ich mir jetzt swiss stop bremsgummis gekauft.....
NBer ist offline   Mit Zitat antworten
Alt 19.07.2018, 22:07   #8
bentus
Szenekenner
 
Registriert seit: 11.06.2012
Beiträge: 1.137
Zitat:
Zitat von iChris Beitrag anzeigen
Wenn du nicht tubeless fährst kannst du auch einfach das Felgenband tauschen. Das blaue Reynolds trägt relativ viel auf. Mit einem dünneren hast du mehr Spiel.
Gibt es da eine Empfehlung in Kombination mit Latexschläuchen?
bentus ist offline   Mit Zitat antworten
Antwort


Themen-Optionen

Forumregeln
Es ist Ihnen nicht erlaubt, neue Themen zu verfassen.
Es ist Ihnen nicht erlaubt, auf Beiträge zu antworten.
Es ist Ihnen nicht erlaubt, Anhänge anzufügen.
Es ist Ihnen nicht erlaubt, Ihre Beiträge zu bearbeiten.

vB Code ist An.
Smileys sind An.
[IMG] Code ist An.
HTML-Code ist Aus.
Gehe zu

Alle Zeitangaben in WEZ +2. Es ist jetzt 02:49 Uhr.

Durchbruch: Was wirklich schneller macht
Persönliche Tipps aus dem Training der Triathlon-Langstreckler Peter Weiss und Arne Dyck
Wettkampfpacing Rad
Nächste Termine
Anzeige:

triathlon-szene.de

Home | Impressum | Datenschutz | Kontakt | Forum

Social

Forum
Forum heute
Youtube
facebook
Instagram

Coaching

Individuelles Coaching
Trainingspläne
Gemeinsam zwiften

Trainingslager

Trainingslager Mallorca
Trainingslager Deutschland
Radtage Südbaden
Alle Camps

Events

Gemeinsamer Trainingstag
Gemeinsames Zeitfahrtraining
Trainingswochenende Freiburg
Trainingswochenende München
Zeitfahren Freiburg
Zwei-Seen-Tour München

TV-Sendung

Mediathek
Infos zur Sendung

Racewear

Trikot und Hose

Rechner

Trainingsbereiche und Wettkampftempo Rad
Trainingsbereiche und Wettkampftempo Laufen
Trainingsbereiche und Wettkampftempo Schwimmen
Profi-Pacing Langdistanz
Vorhersage erste Langdistanz
Altersrechner
Wettkampfpacing 100 km Lauf
Wettkampfgetränk selbst mischen
Powered by vBulletin Version 3.6.1 (Deutsch)
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.